Inovonics EN1215WEOL Manuel d'utilisateur télécharger pdf

6/7/12 05043G © Inovonics, 2012 - www.inovonics.com

EN1215WEOL EchoStream® Universal

Transmitter with Wall Tamper

Installation Instructions

1 Overview

The Inovonics EN1215WEOL wide gap universal transmitter with an

included wall tamper switch has a built-in magnetic reed switch on the

side, with a magnet that supports a 5/8" inch gap. The magnetic reed

switch can be used with both ferrous and non-ferrous material. A 2.2K

ohm end of line resistor is included with the EN1215WEOL, and is

required for operation.

The EN1215WEOL includes a back tamper switch. The tamper condition

must be defined within the control panel as a trouble condion when the

system is disarmed, and as an alarm condition when the system is armed.

Note: For UL installations, refer to the EN4216MR Installation and

Operation Manual, the EN4232MR Installation and Operation Manual, or

the EN7285 Installation Instructions. The switch contact must also be

located in the same room as the EN1215WEOL, and the EN1215WEOL

must be installed in accordance with UL 681 and ULc S302.

Note: The cable length from the switch contact must not to exceed 10

feet.

Caution: The EN1215WEOL contains both a wired input and an input

activated by a reed switch and magnet. The reed switch and magnet

MUST be used unless the application (control panel) specifically supports

both inputs as separate devices. Use of the wired input is optional.

1.1 Inovonics Wireless Contact Information

If you have any problems with this procedure, contact Inovonics technical

services:

• E-mail: support@inovonics.com

• Phone: (800) 782-2709

1.2 EN1215WEOL External Components

Figure 1 EN1215WEOL external components

1.3 EN1215WEOL Internal Components

Figure 2 EN1215WEOL internal components

1.4 What’s In The Carton

• Wall mount screws

• Wall mount anchors

• Selection jumpers

• 3.0V lithium battery

• Housing closure screw

• Magnet

• 2.2K ohm end of line resistor

2 Installation and Startup

2.1 Installation Notes

• These products are designed to be installed and maintained by

professional security technicians.

• Products are intended for indoor use.

• Manually test all products weekly.

2.2 Initial Setup

Battery Installation

1. Insert a small screwdriver to depress the housing release tab on the

bottom of the transmitter; pry the housing apart.

Figure 3 Open the EN1215WEOL Housing

2. Install the new battery.

3. Press the Reset button to initialize the transmitter.

4. Test the transmitter and ensure appropriate response.

Select the Frequency Band

EchoStream products are able to use a range of radio frequencies, and

must be configured for your geographic area. This product ships with a

default frequency range of 902-928 MHz for use in North America. If you

are using the product in North America, skip to step 7; if you are using the

product in Australia or New Zealand, you will need to configure the

transmitter.

5. Place a selection jumper on the appropriate frequency band selection

pins.

• Place the jumper on the right two pins, marked NZ, to set the

frequency range to 921-928 MHz for New Zealand.

• Place the jumper on the left two pins, marked AU, to set the

frequency range to 915-928 MHz for Australia.

Note: Only devices set for use in North America are configured for UL

installations.

6. Press the Reset button to complete configuration.

Caution: When pressing the Reset button, make sure you don’t also

touch the frequency band selection pins. Touching the frequency band

selection pins while pressing the Reset button can inadvertently set the

EN1215WEOL to the wrong frequency band.

Select Input Type and Wire Resistor

The N/O-N/C selection pins allow the choice of a normally open or

normally closed state for the contact circuit wired to the input terminal.

The transmitter is shipped set for normally open, with a selection jumper

on the N/O selections pins.

Set for normally open operation:

7. Place a selection jumper on the selection pins to select normally

open.

8. Use 22 AWG wire to wire the 2.2K ohm resistor in parallel with the N/0

contact per Figure 4. The distance from the external contact to the

EN1215WEOL must not exceed 10 feet (3 meters).

9. Press the Reset button to complete configuration.

Figure 4 Wired for N/O operation

Set for normally closed operation:

10. Remove the selection jumper from the selection pins.

11. Use 22 AWG wire to wire the 2.2K ohm resistor in series with the N/C

contact per Figure 5. The distance from the external contact to the

EN1215WEOL must not exceed 10 feet (3 meters).

12. Press the Reset button.

Figure 5 Wired for N/C operation

A Housing closure screw hole B Wall tamper switch

A Housing tamper button B N/O - N/C jumper

C Input terminal D Reset button

E Wall-mount screw holes F Housing closure screw hole

G Reed switch H Frequency band selection pins

1 2

Résumé du contenu

Page 1 - Transmitter with Wall Tamper

6/7/12 05043G © Inovonics, 2012 - www.inovonics.comEN1215WEOL EchoStream® Universal Transmitter with Wall TamperInstallation Instructions1 OverviewThe

Page 2 - 3.1 Battery Replacement

6/7/12 05043G © Inovonics, 2012 - www.inovonics.comRegister the EN1215WEOLTransmitters must be registered with the system in order to be monitored and

Commentaires sur ces manuels

Pas de commentaire

Inovonics EN1215WEOL Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Communication Inovonics EN1215WEOL. Inovonics EN1215WEOL User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Communication Inovonics EN1215WEOL